Q. i have a linksys wrt120n router and it worked for some time. then it didnt work anymore so i replaced it with a new one. Then i tried to install it again with the cd but it failed. Then i had an error in my computer that forced me to reinstall windows. After reinstalling, i plugged in the router and it worked without any setup. Now it isnt working anymore. I tried resetting it and installing it with the cd. it worked with the cd, and it also installed network magic. I connected my ipad there and the computer said new device found and its status is online. The signal in my ipad is strong but i cannot access the internet at all. i tried installing it again and all but still it didnt work. I tried to do the manual installation but the ip address for linksys ( 192.168.1.1 ) leads to my adsl modem instead of router. In some of the process though , i was able to open the router setup page instead of my modem when in the setup, there was no internet connection for my computer. I tried resseting everything, and also restarting my ipad and reset the network settings but nothing worked for me. i can still open the internet in my computer but not anywhere else
my operating system is windows 7 ultimate 32 bit
Thanx
my operating system is windows 7 ultimate 32 bit
Thanx
A.
how to configure my cisco linksys to factory settings.. model WRT120N..?
Q. i was using my wi-fi initially.. 4 months back.. we disconnected it.. it was with WEP security setting..
now i wish to use my wi-fi again but it says the settings saved on computer for network do not match the requirements of network.. so i need to reset factory settings.. any idea how to do it..
the user manual was not much help to me..
now i wish to use my wi-fi again but it says the settings saved on computer for network do not match the requirements of network.. so i need to reset factory settings.. any idea how to do it..
the user manual was not much help to me..
A. On the back of the router, press and hold the reset button for 10 seconds. And, BTW, do not use WEP, it can be cracked it 15 seconds. Use WPA/WPA2.
My laptop is not gitting internet access on wyfi how do i fix it?
Q. I have a Wes tell modem model G90-610014-20 AND A Linksys wireless router model WRT120N and my friend held the reset button on both the router and the modem for 10 seconds and now when i connect to my WIFI set up i do not get internet access but when i plus the ethernet cord from my modem to my laptop i get a internet connection. I have tried to power down my computer and unplug everything for 10 seconds and plug it back in and i have also tried to unplug the router for 10 seconds and neither worked. What do i do?
A. Your "friend" reset both your modem and router to the factory defaults. Apparently, your modem's factory default settings are sufficient to work on your provider's network, and your router's factory default settings are sufficient to maintain a wired connection to your provider's network. However, your wireless setup generally needs to be configured, unless you want to run with the default network name ("linksys"), the default encryption (none), and the default password (none). And sometimes the factory default is that the wireless card is off, so you won't even get that.
What you need to do is go through the router setup routine again, and keep your friend away from your buttons. The manual for your router is here:
jhttp://homedownloads.cisco.com/downloads/userguide/WRT120N_V10_UG_NC-WEB.pdf
What you need to do is go through the router setup routine again, and keep your friend away from your buttons. The manual for your router is here:
jhttp://homedownloads.cisco.com/downloads/userguide/WRT120N_V10_UG_NC-WEB.pdf
Linksys WRT120N Router and Speedstream 5100. Wifi keeps disconnecting from lap tops!?
Q. Ok so my mom can't quite figure it out. The Wifi keeps disconnecting from our lap tops every so often, (it doesn't happen all the time, but when it does, it's annoying because of how frequent it is) and we have no idea why it keeps happening! We think it has something to do with the neighbors wifi showing up and then disappearing from the possible networks you can choose to connect to!
To the first answer and all proceeding it, my mother doesn't know how to change the channels and what channels to change!
To the first answer and all proceeding it, my mother doesn't know how to change the channels and what channels to change!
A. Go into the router, and change the channel for your wifi network. The non-overlapping channels for an 802.11g and n network in the 2.4 GHz range are 1, 6, 11. So change to one of those, and preferably as far away from your current channel as possible.
Here's a link to the home page for the router. In particular, it is possible to download a PDF of the user guide from that home page. http://homesupport.cisco.com/en-us/wireless/lbc/WRT120N
In particular, you wish to refer to page 10, "Basic Wireless Settings (Manual)".
Here's a link to the home page for the router. In particular, it is possible to download a PDF of the user guide from that home page. http://homesupport.cisco.com/en-us/wireless/lbc/WRT120N
In particular, you wish to refer to page 10, "Basic Wireless Settings (Manual)".
Powered by Yahoo! Answers
No comments:
Post a Comment