Q. I have my main laptop set as the admin for my linksys router and I got an IPad for christmas but I forgot where to go to add its MAC address to the list! Please help! Thanks!
A. By default, a Linksys' ip address is 192.168.1.1. Put that number into the address bar of your internet browser. When prompted for a username/password, enter your info. The default username is blank, and the password is admin. From here, go to the wireless security page. Find the mac filter list. Add the mac address. Done.
What is the ip address to takes you to the Linksys router setup screen?
Q. What is the ip address to takes you to the Linksys router setup screen?
A. Concurs with all answers (that�s default) � however if also can be configured to use any other address starting from:192, 10 or 172.
Should 192.168.1.1 don�t work:
1.Go to prompt command: �START� >> �RUN� >> type �CMD�
2.In new black window type: ipconfig /all
3.Address listed as Default Gatway is your routers private IP
PS.
Default credentials for authentication are: username: blank password: �admin�, depending however on ISP you are using could be anything else (typical: credentials given by ISP used for connecting to Internet)
Should 192.168.1.1 don�t work:
1.Go to prompt command: �START� >> �RUN� >> type �CMD�
2.In new black window type: ipconfig /all
3.Address listed as Default Gatway is your routers private IP
PS.
Default credentials for authentication are: username: blank password: �admin�, depending however on ISP you are using could be anything else (typical: credentials given by ISP used for connecting to Internet)
How to change security on linksys router?
Q. I know my neighbors are accessing my internet via my linksys router. I just went in though the ip address and set up a password. Do I need to do anything else to stop them?
A.
I have a linksys router and im trying to setup wirless internet through a motorola surf board modem?
Q. I plugged the modem into the linksys router (internet port) and had another ethernet cord connecting to the linksys to the computer (when doing this the computer plugged in doesnt even have internet). I dont have a setup disk for the router, and the linksys setup wizard from the site doesnt seem to work.
A. This could be a lot of things.
1. Reset your cable modem. Unplug for 10 seconds, then plug back in
2. hold down the little button on the linksys router (even if brand new) for like 30 seconds. It should reset to factory defaults.
3. Plug modem into internet port on router.
4. Plug computer into a free port on the router.
5. Check computer settings to make sure it does not have a static ip address. you can do this by going to network connections, Local Area Connection (which should show as connected or plugged in), then right clicking and selecting properties. Then look for TCP/IP properties, and you should see the area where you can change the IP and DNS settings. Make sure these are all blank.
6. You can open internet explorer and type 192.168.1.1 Just that. nothing else.
7. it will ask you for username and password. username is admin, password either blank , or admin.
that should get you into router setup.
1. Reset your cable modem. Unplug for 10 seconds, then plug back in
2. hold down the little button on the linksys router (even if brand new) for like 30 seconds. It should reset to factory defaults.
3. Plug modem into internet port on router.
4. Plug computer into a free port on the router.
5. Check computer settings to make sure it does not have a static ip address. you can do this by going to network connections, Local Area Connection (which should show as connected or plugged in), then right clicking and selecting properties. Then look for TCP/IP properties, and you should see the area where you can change the IP and DNS settings. Make sure these are all blank.
6. You can open internet explorer and type 192.168.1.1 Just that. nothing else.
7. it will ask you for username and password. username is admin, password either blank , or admin.
that should get you into router setup.
Powered by Yahoo! Answers
No comments:
Post a Comment